Fireplace insert HEATING 620 straight
- Nominal heat output 10 kW, output range 5–12 kW
- Efficiency 80.7 %, class A+, compliant with EN 13229 and Ecodesign Regulation (EU) 2015/1185
- Body and all components made of P265GH boiler steel plate, 3 mm
- Front glass 600 × 390 mm, raising feet included as standard
- Approximately 80–100 m² with good building insulation
How to choose the glass side?
Trade price list, availability and technical documentation are sent on request.
Request a trade offerHEATING 620 straight – insert description
For installation with a straight glass panel
Fireplace insert with a nominal heat output of 10 kW and a straight front glass panel, 600 × 390 mm. Takes logs up to 500 mm long. Heats approximately 80–100 m² in a building with good insulation standard.
P265GH boiler steel plate, 3 mm
All components of the insert are made from P265GH boiler steel plate, 3 mm thick. This means the insert can be built into a warm, heat-storage (accumulation) enclosure, including a hypocaust-type system without convection grilles. The combustion chamber is lined with ceramic concrete, 3 cm thick, has two baffles and a steel ash pan, and the door uses a copper closing system.
Combustion and emissions
Closed combustion chamber with flue-gas afterburning, fuel: hardwood. At nominal output the insert reaches an efficiency of 80.7 % and class A+. Emissions: particulate matter 40, organic gaseous compounds 60, carbon monoxide 1243 and nitrogen oxides 126 mg/m³. The insert is suited to homes with heat-recovery ventilation.
Compliance with standards
Heating Holding of Bydgoszcz declares that the insert complies with the harmonised standard EN 13229 and with the Ecodesign requirements of Commission Regulation (EU) 2015/1185. Testing was carried out by notified body No. 1450, Kraków. The declaration of conformity can be downloaded below.
The version with a side glass is the HEATING 620 corner. Higher output, 11 kW: HEATING 720 straight.
Technical specification
Source: declaration of conformity for HEATING 620 straight and manufacturer's technical dataOutput and fuel
Emissions at nominal output
Dimensions and glass
Construction and compliance
Technical drawing
Click the drawing to open it in full resolution.Downloads
Declaration of conformity (PL)HEATING 620 straight · PDFTechnical drawingJPGOther technical documents are available on request.
Questions and answers
Frequently asked questions about HEATING 620 straight. Can't find yours? Write to us.
Ask about this modelWhat is the output and efficiency of the HEATING 620 straight?
The nominal heat output is 10 kW (output range 5–12 kW), and efficiency at nominal output is 80.7 %. Energy efficiency class: A+.
What floor area will it heat?
Approximately 80–100 m² in a building with a good insulation standard and an open room layout. The actual reach depends on insulation, building layout and how the warm air is distributed.
What fuel should be used?
Hardwood – the manufacturer tested and declares the insert's parameters on this fuel. Fuel consumption is around 2 kg/h.
Which standards does it comply with?
The harmonised standard EN 13229 and the Ecodesign requirements of Commission Regulation (EU) 2015/1185. Testing was carried out by notified body No. 1450, Kraków.
Can it be installed in a heat-storage enclosure?
Yes. The body and all components are made of P265GH boiler steel plate, 3 mm, so the insert is suited to a warm, heat-storage (accumulation) enclosure, including a hypocaust-type system, without convection grilles.
How do I order larger quantities?
Send an enquiry through the form at the bottom of the page, or contact the sales department: tel. +48 507 301 323, m.bienias@heatingpoland.eu. Trade price list and availability on request.
Similar models
All: steel inserts
| Parameter | HEATING 620 straight | HEATING 620 corner | HEATING 720 straight | HEATING PRO M 16 |
|---|---|---|---|---|
| Nominal output | 10 kW | 10 kW | 11 kW | 16 kW |
| Efficiency | 80.7 % | 80.1 % | 80.5 % | 78.2 % |
| Energy class | A+ | A+ | A+ | A |
| Weight | 114 kg | 110 kg | 123 kg | 160 kg |
| Dimensions (H × W × D) | 1152 × 676 × 470 mm | 1180 × 670 × 470 mm | 1200 × 850 × 470 mm | 885 × 870 × 510 mm |
| Flue outlet | 180 mm | 180 mm | 180 mm | 180 mm |
| CO (mg/m³) | 1243 | 673 | 1003 | 1481 |
Work directly with the manufacturer
Offer for distributors, installers and fireplace showrooms. Tell us which models and quantities you are interested in and we will prepare a quotation.